FonoSIP.com
lang world mobile site

CISCO ATA-186

Instruction on adjustment of Cisco ATA 186 or 188.

Connect Cisco ATA 186 to Internet, to power supply and to telephone devices. It is sufficient to have one telephone device, connected to the line No. 1. Telephone device should work in tone dialing mode.

If DHCP is used in your network, Cisco ATA 186 receive an address automatically. To learn what exactly address Cisco ATA 186 is received, it is necessary:

1. Rise the hand set on telephone device, connected to the line 1.

2. Press big button, located on upper panel of Cisco ATA 186.

3. In telephone hand set you will hear an invitation to enter commands.

4. Enter [ 2 ][ 1 ][ # ], after that Cisco ATA 186 will say its IP-address in English.

5. Put the hand set on telephone.

If DHCP is not used in your network, you need to set IP-address and other parameters using telephone set.

1. Rise the hand set on telephone, connected to line 1.

2. Press big button, located on the upper panel of Cisco ATA 186.

3. In telephone hand set you will hear an invitation to enter commands.

4. Dial [ 2 ][ 0 ][ # ][ 0 ][ # ] for disconnection of DHCP, after that Cisco ATA 186 will say in voice entered value and propose to press: [ 1 ] for changing [ 2 ] for repeating [ 3 ] for saving [ 4 ] for return to previous value [ # ] for exit to main configuration menu

5. Enter [ 1 ][ # ][ 1 ][ 1 ][ 1 ][ * ][ 2 ][ 2 ][ 2 ][ * ][ 3 ][ 3 ][ * ][ 4 ][ 4 ][ # ] for entering IP-address 111.222.33.44, than [ 3 ] for saving the parameter. We draw your attention, that instead of 111.222.33.44 you need to enter your IP-address, which was allotted to you by Internet-provider or by network administrator.

6. Enter [ 1 ][ 0 ][ # ][ 2 ][ 5 ][ 5 ][ * ][ 2 ][ 5 ][ 5 ][ * ][ 2 ][ 5 ][ 5 ][ * ][ 0 ][ # ] for entering subnet mask 255.255.255.0 and than dial [ 3 ] for saving the parameters.

7. Enter [ 2 ][ # ][ 8 ][ 2 ][ * ][ 1 ][ 4 ][ 6 ][ * ][ 5 ][ 1 ][ * ][ 3 ][ 2 ][ # ] for entering router address 82.146.51.32 and than dial [ 3 ] for saving the parameter.

Check your flash software version

Connect to your cisco ata 186 using a web browser and pointing to http://ipaddress/dev where ipaddress is the IP address of your ATA 186. On the displayed web page check that it says Cisco ATA 186 (SIP) Configuration on the top. This confirms that you have a SIP capable Image

Also check on the bottom that the software version is ata0011215a28a8. This means that you have software version 2.15. (2.13 or lower need to be upgraded)

If not you need to upgrade the flash image of your cisco ata. To do it follow the instructions at the cisco on-line manual or contact us.

Web Interface Configuration

Open the web browser to
http://ipaddress/dev, where ipaddress is the IP address of your ATA 186. On the displayed web page do the following:

Set UseTftp to 0
Set UID0 to your fonosip.com account's (e.g. 81212).
Set PWD0 to your fonosip.com account's password.
Set GkOrProxy to fonosip.com
Set UseSIP to 1
Set SipPort to 5060
Set DNSServer to 200.0.185.100 (or your local DNS server)
Set SipRegOn to 1
Set LBRCodec: to 3
Set RxCodec: to 3
Set TxCodec: to 3
For NAT only:
Set ConnectMode: to 0x00460400
Set NatServer: to fonosip.com
Set NatTimer: to 0x0000000a
Press the Apply button at the bottom of the web page, then restart the ATA 186 by powering it off and then on again.

-- FonoSIP.com -- Search Site -- About Us -- Add Credit -- Mobile Site -- Login -- Service Numbers -- Help -- Swag -- Write to us info@fonosip.com -- Voicemail 1-360-226-7665 -- FonoSIP.com © 2010

Powered by BA.net iGames


FonoSIP.com supports Xten / Counterpath SIP softphones for Windows, Mac, iPhone and Linux. Internet telephony equipment such as Linksys PAP2, Cisco, Sipura, Nokia N71. Apple iPhone, iPod Touch, iPad. Android. Codec G729. Fring Mobile. Bring your Own Device BYOD. We also support SIP Trunking, replace your phone lines. Asterisk PBX, TrixBox.